TEKBOX EMV Zubehör - Active Load

TBOH02 Self Powered Active Load

Overview
The TBOH02 is a self powered, precision active load. It does not need a separate supply voltage and operates as low as 2V. Its features include constant resistance and constant current mode. A 10 turn potentiometer with dial, a range switch and a precision reference enable accurate setting of current or resistance. Furthermore it can be controlled by an external voltage.
The design is fully analog. Supply noise measurements using the TBOH02 as load will not be superimposed with additional noise in contrary to such measurements carried out with digitally controlled active loads.
The TBOH02 can not only be used as active load for power supply measurements, but also as current sink or current source for power LED testing and similar applications. It also comes handy when carrying out tests in the field, where no external power is available.

The TBSOH02 operates from 2V to 70V. The maximum current is up to 10A, however it has to be taken care that the maximum power without additional cooling is limited to 25W. A fan accessory which can be clipped onto the heat sink increases the maximum power rating to 100W.
The design is based on the EDN, August 2005 article Precision active load operates as low as 2V by Joel Setton
By courtesy of Joel Setton, Crolles, France


Fragen Sie uns an für eine Offerte! >>> Kontakt

Specifications

Operating voltage range: 2V – 70V
Maximum current: 10A
Power rating: max. 25W continuously; with additional fan 100W continuously
Ranges: 0A – 1A, 0A – 10A, 1Ω - 10Ω, 10Ω - 100Ω
External voltage control input

Datenblatt >>>> TBOH02-manual.pdf [452 KB]

The review (Active Load) starts at 30:28

 

245.00 CHF

Artikel-Nr: TBOH02  

incl. 7.7% MwSt. zzgl. Versand

ca. 10 Arbeitstage Lieferzeit  
 
Anzahl:   St



NEW: TBAS1 RF Attenuator Set The TBAS1 RF attenuator set consists of a 3dB, 6dB, 10dB and 20dB attenuator in a beech wood box 135.00 CHF

NEW: TBAS2 SMA Attenuator/Termination The TBAS2 RF SMA attenuator/termination set consists of a 3dB, 6dB, 10dB, 15dB, 20dB and 30dB SMA attenuators in a beech wood box 199.00 CHF

NEW: TBAS3 - 10W N RF Attenuator Set The TBAS3 RF attenuator set consists of a 3dB, 6dB, 10dB and 20dB attenuator in a beech wood box 199.00 CHF

NEW: TBST120/60/60/2 Shielded Tent The TBST-120/60/60/2 is a shielded tent, designed to suppress interference from ambient noise during EMC pre-compliance measurements. With a size of 120 cm x 60 cm x 60 cm, it can accommodate any Tekbox pre-compliance test equipment such as LISNs or TEM-cells 2'975.00 CHF

NEW: TBCP1-150 RF Current Monitoring Probe The TBCP1-150 is a fixed aperture RF current monitoring probe, expanding the Tekbox product range of affordable EMC pre-compliance test equipment. The probe has a 3dB bandwidth of approximately 150 MHz and is characterized and usable over the frequency range from 10kHz to 250 MHz. The aperture of the RF current monitoring probe is 25 mm. Its transfer impedance is > 14 dB Ohm in the range from 100 kHz to 150 MHz. 495.00 CHF

NEW: TBCG1 Radiating Comb Generator TBCG1 Radiating Comb Generator 145.00 CHF

NEW: TBCG2 Comb Generator TBCG2 Comb Generator 145.00 CHF

TBLC08- LISN 50uH TEKBOX EMV Zubehör - EMV Precompliance - LISN TBLC08 50uH Line Impedance Stabilisation Network LISN - CISPR 16 985.00 CHF

TBOH01 - LISN 5uH 5uH Line Impedance Stabilisation Network LISN - CISPR 25The TBOH01 5µH LISN is a device required to setup conducted noise measurements of DC-powered devices. It is designed to be used for EMC pre-testing in the frequency range of 150kHz to 110 MHz 375.00 CHF