TBTC1 - 50mm - TEM Cell for EMC Pre-Compliance Testing
Overview
A TEM cell is a stripline device for radiated emissions and immunity testing of electronic devices. It is not a replacement, but due to its size and cost it is a convenient alternative to measurements in an anechoic chamber.
A TEM cell consists of a septum, the conductive strip in the centre section and walls which are connected to ground. The geometry is designed to present a 50Ω stripline. The device under test (DUT) is placed in between the bottom wall and the septum.
The TBTC1 is a so called “open TEM cell”, which got no side walls for convenient placement of the DUT. It may pick up RF background noise, which however can be taken into account by doing a measurement of the cell output signal before powering on the DUT.
The TBTC1 is designed for frequencies up to 700MHz, however it can also be used at frequencies beyond 1GHz.
The device is supplied together with a 50Ω/25W RF termination and a DC block to protect the spectrum analyzer or RF receiver input.
Radiated emission tests: the septum of the TEM cell picks up radiated noise from the DUT, similar to a broadband antenna, and presents it to the analyzer input.
Radiated immunity tests: the TEM cell will be connected to the output of a swept signal generator + RF amplifier and the septum radiates into the DUT.


Specifications


TBTC1 TEM cell dimensions:
Length: 390 mm
Width: 200 mm
Height: 108 mm
Septum height: 50 mm

Rectangular area under the septum: 19 cm x 13 cm x 5 cm

TEM cell connectors: N-female
Nominal cell impedance: 50 Ohm
Wave impedance: 377 Ohm
Maximum RF input power: 25W (limited by supplied 50 Termination)
Input return loss: S11 up to 1.2 GHz < -20dB, up to 2.1 GHz < -17dB, up to 3GHz < -14dB
Transmission loss: up to 1.4 GHz < 1 dB, up to 2.1 GHz < 3dB, up to 3 GHz < 6dB

Ein ausführliches Datenblatt finden Sie hier:

Documentation
tekbox-tem-cell-manual [561 KB]

 

915.00 CHF

Artikel-Nr: TBTC1  

incl. 7.7% MwSt. zzgl. Versand

ca. 10 Arbeitstage Lieferzeit  
 
Anzahl:   St



NEW: TBAS1 RF Attenuator Set The TBAS1 RF attenuator set consists of a 3dB, 6dB, 10dB and 20dB attenuator in a beech wood box 135.00 CHF

NEW: TBAS2 SMA Attenuator/Termination The TBAS2 RF SMA attenuator/termination set consists of a 3dB, 6dB, 10dB, 15dB, 20dB and 30dB SMA attenuators in a beech wood box 199.00 CHF

NEW: TBAS3 - 10W N RF Attenuator Set The TBAS3 RF attenuator set consists of a 3dB, 6dB, 10dB and 20dB attenuator in a beech wood box 199.00 CHF

NEW: TBST120/60/60/2 Shielded Tent The TBST-120/60/60/2 is a shielded tent, designed to suppress interference from ambient noise during EMC pre-compliance measurements. With a size of 120 cm x 60 cm x 60 cm, it can accommodate any Tekbox pre-compliance test equipment such as LISNs or TEM-cells 2'975.00 CHF

NEW: TBCP1-150 RF Current Monitoring Probe The TBCP1-150 is a fixed aperture RF current monitoring probe, expanding the Tekbox product range of affordable EMC pre-compliance test equipment. The probe has a 3dB bandwidth of approximately 150 MHz and is characterized and usable over the frequency range from 10kHz to 250 MHz. The aperture of the RF current monitoring probe is 25 mm. Its transfer impedance is > 14 dB Ohm in the range from 100 kHz to 150 MHz. 495.00 CHF

NEW: TBCG1 Radiating Comb Generator TBCG1 Radiating Comb Generator 145.00 CHF

NEW: TBCG2 Comb Generator TBCG2 Comb Generator 145.00 CHF

TBLC08- LISN 50uH TEKBOX EMV Zubehör - EMV Precompliance - LISN TBLC08 50uH Line Impedance Stabilisation Network LISN - CISPR 16 985.00 CHF

TBOH01 - LISN 5uH 5uH Line Impedance Stabilisation Network LISN - CISPR 25The TBOH01 5µH LISN is a device required to setup conducted noise measurements of DC-powered devices. It is designed to be used for EMC pre-testing in the frequency range of 150kHz to 110 MHz 375.00 CHF